• Offer Profile
  • The up-to-date development, research and production facilities of JVL employ only the latest technology for the development and production of electronic controls for step- and servo motors. More than 50% of the staff are engineers with a very high degree of experience and competence in the field of motion control. They are all highly motivated and innovative, and we can therefore offer a product program today that includes all the necessary units and components to build up complete motor control systems.
Product Portfolio
  • QuickStep - Integrated Stepper Motors

  • The MIS motor - the complete motion solution Stepper motor with integrated controller All necessary components in one unit

    The basic idea of the MIS motor is to minimize the installation costs but also to make a component that is much better protected against electrical noise which can be a problem when using long cables between controller and motor. The stepper motor, hallsensor, encoder and electronics are specially developed by JVL so that they together form an enclosed unit where the power driver and controller are mounted inside the motor in a closed section. The MIS motors can be delivered in sizes of 0.36 to 25.0.

    Adapt your motor to your application with firmware

    JVL MIS Integrated Servo Motors can be delivered with different numbers of M12 connectors depending on the application. MIS17x and MIS23x motors can be delivered with RS485 interface and PLC built-in and optional CANopen. MIS34x and MIS43x have RS485 and PLC built-in and optional Profinet, EtherCAT, Ethernet/IP, Powerlink or MODBUS TCP/IP interface. All MIS motors have optional magnetic absolute encoder built-in and MIS34x and MIS43 have optional absolute multiturn encoder built-in.

      • MIS171-MIS176 QuickStep - NEMA17 Programmable Integrated ServoStep Motors with Closed-Loop, Ethernet, multiturn encoder

        • MIS171 - 0.15Nm
        • MIS173 - 0.26Nm
        • MIS176 - 0.80Nm

        QuickStep, the Integrated ServoStep Motors from JVL.
        All in one smartmotor with integrated controller. A wealth of possibilities with this new NEMA17 stepper with closed-loop servo-operation up to 3000RPM, It offers the highest microstepping resolution, position/velocity/torque servo-performance up to 0.8Nm.

        Available with CANbus, RS485, SSI, Industrial Ethernet Profinet, Ethercat, Ethernet/IP, Powerlink, Ethernet TCP, Sercos III , Absolute multiturn encoder, PLC 8IOA, clock/direction and STO.
        Velocity resolution 0,01RPM for extreme low speed operation and 409600 step/rev for highest precision. Different shaft diameter, brakes and high IP protection make it ideal for machine adjustment or other demanding applications.

         

      • MIS231-MIS234 Quickstep - NEMA23 Programmable Integrated ServoStep Motors with Closed-Loop, Ethernet, multiturn encoder

      • QuickStep, the Integrated ServoStep Motors from JVL. A wealth of possibilities in a NEMA23 series of the world´s most compact stepper motors with the highest microstepping resolution, closed-loop 3000RPM and up to 3.1Nm.

        Available with standard steppermotor or new hybrid steppermotor technology with rare earth magnets in rotor giving +40% more torque in same size.

      • MIS231- MIS234 Quickstep – NEMA23 Programmable Integrated ServoStep Motors with Closed-Loop, Ethernet, multiturn encoder

      • QuickStep, the Integrated ServoStep Motors from JVL. 
        A wealth of possibilities in a NEMA23 series of the world´s most compact stepper motors with the highest microstepping resolution, closed-loop 3000RPM and up to 3.1Nm. 

        Available with standard steppermotor or new hybrid steppermotor technology with rare earth magnets in rotor giving +40% more torque in same size.
      • MIS340-MIS343 QuickStep - NEMA34 Programmable Integrated ServoStep Motors with Closed-Loop, Ethernet, multiturn encoder

      • QuickStep, the Integrated ServoStep Motors from JVL.
        A wealth of possibilities in a series of of the world´s most compact stepper motors with the higest microstepping resolution. 4 sizes are available.

        • MIS340 - 3.0/2.7Nm
        • MIS341 - 6.0/5.3Nm
        • MIS342 - 9.0/7.4Nm
        • MIS343 - 12.0/9.9Nm

        The QuickStep series of Stepper motors with integrated electronics represents a major step forward. All the necessary electronics in a stepper system are integrated in the motor itself.
        The stepper motor, encoder and electronics are specially developed by JVL so that together they form a closed unit in which the power driver and controller are mounted inside the motor in a closed section with protection up to IP67, and stainless steel shaft AISI303 as standard on all models.

        Choose between wireless Bluetooth, WLAN or Zigbee or Industrial Ethernet Profinet, Ethernet/IP, EtherCAT, Powerlink, MODBUS TCP/IP, RS485 and PLC built-in are standard.

      • 10.0-25.0Nm - MIS43x QuickStep - Integrated Stepper Motors

      • QuickStep, the Integrated Stepper Motors from JVL.
        A wealth of possibilities in a series of the world´s most compact stepper motors with the highest microstepping resolution. 2 sizes are available.
         
        • MIS430 - 10.0Nm
        • MIS432 - 25.0Nm

        The QuickStep series of Stepper motors with integrated electronics represents a major step forward. All the necessary electronics in a stepper system are integrated in the motor itself.

        The stepper motor, encoder and electronics are specially developed by JVL so that together they form a closed unit in which the power driver and controller are mounted inside the motor in a closed section with protection up to IP67. Choose between wireless Bluetooth, WLAN or Zigbee or Industrial Ethernet Profinet, Ethernet/IP, EtherCAT, Powerlink, MODBUS TCP/IP, RS485 and PLC built-in are standard.

      • MAC motor®s - Integrated servo motors from 50 W up to 3000 W

      • The MAC motor - the complete motion solution Brushless servo motor with integrated controller - All necessary components in one unit
        Integrated motors mean that Motor, Hall Sensors, Encoder and Servo Controller are all built into one unit. By adding various option modules, MAC motors can be controlled by ±10 VDC, Pulse/Direction signal or serial commands. With programmable modules MAC motors can act as stand-alone units.
        Subsequent advantages of using MAC motor®s:
        • You save space in your control cabinet
        • You save expensive shielded motor and encoder cables
        • You save time and money for cabling
        • Installation errors between driver and motor are eliminated
        • Noise is minimized due to internal cabling
        Adapt your motor to your application with Expansion Modules

         The JVL MAC Integrated Servo Motors utilize the unique module concept. Plug-in expansion modules adapt the motor to the application. You can choose connector type: D-Sub, cable glands or M12 connectors. We offer the widest range of control modules: all major Industrial Ethernet types (EtherCAT, EtherNet/IP, Powerlink, Profinet, Modbus TCP and Sercos III) and fieldbusses (Profibus, DeviceNet and CANopen) or Nano PLC control. Furthermore we offer Wireless modules e.g. Bluetooth, IEEE 802.15.4 and WLAN. Also we have RS232/RS485 serial communications modules.
        This means that the MAC motor gives you possibilities no other motors on the market can provide. Also important, you only pay for what you need. In addition, if you do not find the features you require, please contact us, and we will develop your own customized module.
          • MAC050 - 141 - Integrated Servo Motors: 0.11-0.48Nm/4000rpm

          • MAC050 to MAC141- the complete solution for lower power ratings.
            • Choose between 4 sizes of motor.
            • From 50W to 141W.
            • Also in IP67 versions.
            • Choose Expansion module from the extensive selection for any application.

            Expansion module you can choose between:

            • Basic Modules
            • Programmable Modules
            • Field Bus Modules
            • High Speed Multi-Axis Modules
            • Wireless Modules

             

          • MAC400 Integrated Servo Motor 115 to 230VAC: 1.3Nm/3000rpm

          • MAC400 - The complete solution for medium power ratings.

            • With built-in mains power supply.
            • Choose between model with or without brake.
            • Also in IP66 version.

            New features:

            • Absolute multiturn encoder without battery
            • Real-time industrial Ethernet: Profinet, Ethernet/IP, MODBUS TCP, EtherCAT, Powerlink and SercosIII
            • 2 RS422 channels for encoder in/output and SSI encoder etc.
            • 6IO for capture of position, interrupt, counters, enable, timer and PLC functions

            Expansion module you can choose between:

            • Basic Modules
            • Programmable Modules
            • Field Bus Modules
            • High Speed Multi-Axis Modules
            • Wireless Modules
          • MAC402 Integrated Servo Motor 12-48VDC: 1.3Nm/3000rpm

          • MAC402 - The complete 400W solution for medium power ratings with battery supply 12-48VDC.
            • The complete 400W solution for medium power ratings with battery supply 12-48VDC.
            • Peak power up to 1200W.
            • Choose between model with or without brakes.
            • IP55 standard. IP66 optional.
            • Wireless, Industrial Ethernet or PLC build in.

            New features:

            • Absolute multiturn encoder without battery
            • Real-time industrial Ethernet: Profinet, Ethernet/IP, MODBUS TCP, EtherCAT, Powerlink and SercosIII
            • 2 RS422 channels for encoder in/output and SSI encoder etc.
            • 6IO for capture of position, interrupt, counters, enable, timer and PLC functions

            Expansion module you can choose between:

            • Basic Modules
            • Programmable Modules
            • Field Bus Modules
            • High Speed Multi-Axis Modules
            • Wireless Modules
          • MAC800 - Integrated Servo Motors: 2.4Nm/3000rpm

          • MAC800 - The complete solution for larger power ratings.
            • All with built-in mains power supply.
            • Choose between model with or without brake.
            • Also in IP66 version.
            • Choose Expansion module from the extensive selection for any application.

            Expansion module you can choose between:

            • Basic Modules
            • Programmable Modules
            • Field Bus Modules
            • High Speed Multi-Axis Modules
            • Wireless Modules
          • MAC1500 - 3000 - Integrated Servo Motors: 4.5-9.0Nm/3000rpm

          • MAC1500-3000 - The complete solution for larger power ratings. All with built-in mains power supply.
            • Choose between model with or without brake.
            • From 1.5kW to 3.0kW.
            • Choose Expansion module from the extensive selection for any application.

            Expansion module you can choose between:

            • Basic Modules
            • Programmable Modules
            • Field Bus Modules
            • High Speed Multi-Axis Modules
            • Wireless Modules

            Most of them available with either cable glands, DSUB connectors and M12 connectors. 

             

          • Stainless steel MACmotor 370W peak, MAC100 and MAC101

          • It's now possible to have a MAC141 in a stainless steel housing and in a IP67 version.

            Different modules with M12 connectors can be chosen:

            • Basic Modules
            • Programmable Modules
            • Field Bus Modules
            • High Speed Multi-Axis Modules
            • Wireless Modules

            Gears with different ratios can also be chosen for these applications.

          • Water Resistant Versions of MAC050 - 141 

          • IP67 Versions of MAC140 or MAC141
            Resistant against rough chemicals
            • Cost-Effective in harsh wet environment
            • Ideal for food processing, pharmaceutical and chemical industries
            • A double shaft seal and leak-proof cable entry provide watertight sealing
            • A thick protective layer of epoxy surface treatment is bonded to the motor body
            • Stainless steel shaft and flange
            • For orders more than 50 pcs. the motor can be painted in colors other than green and white.
        • Industrial Ethernet for MAC

        • Industrial Ethernet is the name given to the use of the Ethernet network protocol in an industrial environment, for automation and process control.
          A number of techniques are used to adapt the Ethernet protocol for the needs of industrial processes, which must provide real time behavior.
              • By using non-proprietary protocols, automation systems from different manufacturers can be interconnected throughout a process plant.

                Industrial Ethernet takes advantage of the relatively larger marketplace for computer interconnections to reduce cost and improve performance of communications between industrial controllers.

                Industrial Ethernet (IE) components used in plant process areas must be designed to work in harsh environments of temperature extremes, humidity, and vibration that exceed the ranges for IT equipment intended for installation in controlled environments.


                Ethernet modules for JVL MAC servo motors:
                • EtherCAT
                • EtherNet/IP
                • PROFINET IO
                • SERCOS III
                • Modbus TCP
                • Powerlink
          • Stepper Motor Drivers

          • A series of stepper motor drivers that meets almost all the needs for precise control of stepper motors, incuding mini-stepping with up to 25000 ministeps per revolution.
              • Stepper Motor Ministep Drivers SMD41 and SMD42

              • These Stepper Motor Drivers are compact ministep drivers which can drive stepper motors up to 9Amp./phase (RMS). 13 different models provide various motor currents and step resolutions up to 25000 steps/motor revolution.
              • Stepper Motor Driver SMD73

              • SMD73 is a miniature stepper motor driver that is ideal for direct mounting onto a stepper motor, but can of course also be mounted on a surface. The driver can supply from 0-3A RMS in each phase and current is automatically regulated to 1/3 when the motor is not receiving step pulses.
              • Stepper Motor Driver SMD74 (Pulse/ Direction)

              • SMD74 is a miniature driver 18-48VDC that measures only 52.4x52.4 mm and is ideal for direct mounting onto a step motor. It fits onto most types of high-torque motors, but of course can also be mounted on a surface or in a box.
              • Multifunction Stepper Motor Driver PA0076

              • An advanced multi-function stepper motor driver which can be controlled both by external step pulses, but also from an internal step generator.
            • Stepper Motor Controllers

            • A PCB, small Stepper Motor Controller with PLC, CANopen and 8IO
                • Stepper Motor Controller SMC75

                • Stepper Motor Controller with PLC, CANopen and 8IO

                  A Stepper Motor Controller with RS485 and CANbus serial interface. 8IO can be configured to input, output or analog input. Can be controlled via nanoPLC and MacTalk. The very compact, 57x57mm, PCB contains everything needed to solve a modern control task as stand-alone or controlled from a PLC or PC. MODBUS RTU and CANopen gives the possibility for easy connection to a PLC. For PC or IPC an ActiveX/OCX driver is available so that interface to LABview, Excel, VB or other Windows-programs is simple.

                  • NanoPLC with 8IO in 24
                  • RS485 up to 962kbit
                  • CANOpen DSP402
                  • MODBUS RTU
                  • Resolution up to 1600 step/rev.
                  • Pulse/Direction mode
                  • Supply 12-48VDC
                  • Motor current 0-3Amp RMS
                  • Dual supply for safe emergency stop
                  • Active X / OCX driver available


                  The PCB can be mountet in an instrument or be mounted directly on the back of the motor. Alternatively it can be delivered in a box with cables out or with M12 connectors. The box can be mounted on a buttom plate or on DIN rail. Click here to read more about MIS23x integrated stepper motor solutions.

                • Stepper Motor Controller SMC75 with Housing

                • Stepper Motor Controller with PLC, CANopen and 8IO

                  A Stepper Motor Controller with RS485 and CANbus serial interface. 8IO can be configured to input, output or analog input. Can be controlled via nanoPLC and MacTalk. The very compact, 57x57mm, PCB contains everything needed to solve a modern control task as stand-alone or controlled from a PLC or PC. MODBUS RTU and CANopen gives the possibility for easy connection to a PLC. For PC or IPC an ActiveX/OCX driver is available so that interface to LABview, Excel, VB or other Windows-programs is simple.

                  • NanoPLC with 8IO in 24
                  • RS485 up to 962kbit
                  • CANOpen DSP402
                  • MODBUS RTU
                  • Resolution up to 1600 step/rev.
                  • Pulse/Direction mode
                  • Supply 12-48VDC
                  • Motor current 0-3Amp RMS
                  • Dual supply for safe emergency stop
                  • Active X / OCX driver available


                  The PCB can be mountet in an instrument or be mounted directly on the back of the motor. Alternatively it can be delivered in a box with cables out or with M12 connectors. The box can be mounted on a buttom plate or on DIN rail. Click here to read more about MIS23x integrated stepper motor solutions.

                • Stepper Motor Controller SMC85

                • Stepper Motor Controller with PLC, CANopen and 8IO

                  A Stepper Motor Controller with RS485 and CANbus serial interface. 8IO can be configured to input, output or analog input. Can be controlled via nanoPLC and MacTalk. The very compact, 78.4x86.2mm, PCB contains everything needed to solve a modern control task as stand-alone or controlled from a PLC or PC. MODBUS RTU and CANopen gives the possibility for easy connection to a PLC. For PC or IPC an ActiveX/OCX driver is available so that interface to LABview, Excel, VB or other Windows-programs is simple.

                  • NanoPLC with 8IO in 24V
                  • RS485 up to 962kbit
                  • CANOpen DSP402
                  • MODBUS RTU
                  • Resolution is 409.600 step/rev.
                  • Velocity precission 0,01 RPM
                  • Pulse/Direction mode
                  • Supply 12-80VDC
                  • Motor current 0-9 Amp RMS
                  • Dual supply for safe emergency stop
                  • Active X / OCX driver available
                • Stepper Motor Controller SMC85 with Housing

                • Stepper Motor Controller - programmable with 8 IOs and several options

                  A Stepper Motor Controller with RS485 and CANbus serial interface. 8IO can be configured to input, output or analog input. Can be controlled via nanoPLC and MacTalk. The very compact, 78.4x86.2mm, PCB contains everything needed to solve a modern control task as stand-alone or controlled from a PLC or PC. MODBUS RTU and CANopen gives the possibility for easy connection to a PLC. For PC or IPC an ActiveX/OCX driver is available so that interface to LABview, Excel, VB or other Windows-programs is simple.
                  • NanoPLC with 8IO in 24V
                  • RS485 up to 962kbit
                  • Compatible with all Ethernet protocols (optional)
                  • CANOpen DSP402 (optional)
                  • MODBUS RTU
                  • Resolution up to 819.200 step/rev.
                  • Velocity precission 0,01 RPM
                  • Pulse/Direction mode
                  • Supply 12-80VDC
                  • Motor current 0-9 Amp RMS
                  • Dual supply for safe emergency stop
                  • Active X / OCX driver available
              • High Torque Stepper Motors

              • A wide range of stepper motors, from 18 Nm to 50 Nm. All designed by JVL for use with the entire range of JVL step motor drivers and controllers.
                  • Stepper Motors MST081A03 and MST82A03

                  • Two mini stepper motors for applications where small size is a must.

                    20mm (0.8 inches) NEMA08
                    0.01Nm - 0.03Nm

                    The small mini step motors MST081A08 and MST082A08 are designed to be used in applications where dimensions and weight must be as small as possible. Both have flanges of only 20x20mm and where MST081 is 33mm in length, MST is 42, but then also includes double shaft. The motors can be connected directly to the range of JVL drivers

                  • Stepper Motors MST11x

                  • Mini stepper motor for applications where small size is a must.

                    28mm (1.1 inches) NEMA11
                    1.2Nm - 4.0Nm

                    The small mini steppper motors MST11xA with or without planetary gear are designed to be used in applications where dimensions and weight must be as small as possible. Motor flanges are 28x28mm and motor length 31mm to 50mm.

                    Planetary gear with reductions ratio from 3.71 to 369:1 can be mounted and thereby offer short time torque up to 12Nm.

                  • Stepper Motors MST17xxx3

                  • A series of high torque stepper motors.

                    43mm (1.7 inches) NEMA17
                    0.12Nm - 0.8Nm (17.0 oz-in) - (113.3 oz-in)

                    A series of step motors that have been designed by JVL for use with the entire range of JVL Step Motor Drivers and Controllers. They are high torque step motors especially made for mini- and microstep operation.

                    • Highest torque density rating in the industry
                    • High torque-to-inertia for faster start and stop
                    • Rugged design and long life bearings
                    • High power, cooler running, rare-earth magnet design
                    • Exposed-lamination housing, optimized for high torque and smooth, accurate microstepping
                    • Standard NEMA17 mounting
                    • Facilities for encoders, double shaft, different shaft types, etc.
                    • Ground terminal for correct EMC shielding
                    • High axial and radial shaft load
                    • Cost-effective alternative to servo motors
                    • Low noise Option for planetary gearhead
                  • Stepper Motors MST17xxx2

                  • A series of high torque stepper motors with high precision.

                    43mm (1.7 inches) NEMA17
                    0.07Nm - 0.46Nm (9.9 oz-in) - (65.14 oz-in)

                    A series of step motors that have been designed by JVL for use with the entire range of JVL Step Motor Drivers and Controllers. They are high torque step motors especially made for mini- and microstep operation.
                    Compared to the motor MST17xxx3 this motor is produced in higher quality with less mechanical and electrical tolerances making it more suitable for applications that require repetitive and uniform motors. It also offers better protections against water and use better balls bearings etc.

                    • Highest torque density rating in the industry
                    • High torque-to-inertia for faster start and stop
                    • Rugged design and long life bearings
                    • High power, cooler running, rare-earth magnet design
                      Exposed-lamination housing, optimized for high torque and smooth, accurate microstepping
                      Standard NEMA17 mounting
                      Facilities for encoders, double shaft, different shaft types, etc.
                      Ground terminal for correct EMC shielding
                      High axial and radial shaft load
                      Cost-effective alternative to servo motors
                      Low noise Option for planetary gearhead
                  • Stepper Motors MST23xxx3

                  • A series of high torque stepper motors.

                    57mm (2.3 inches) NEMA23
                    0.48Nm - 2.6Nm (68.0 oz-in) - (368.2 oz-in)

                    Compact, high torque step motors

                    The step motors MST001A, MST002A and MST234B03 are designed and dimensioned by JVL for use with the entire range of JVL step motor drivers and controllers.

                    These motors are in particular well-suited for OEM applications. Type MST001A is available in a special version, MST001A-73, for easy back-mounting of the Step Motor Driver
                    SMD73.

                  • Stepper Motors MST23xxx2

                  • A series of high torque stepper motors with high precision.

                    57mm (2.3 inches) NEMA23
                    0.32Nm - 2.1Nm (45.3 oz-in) - (297.4 oz-in)

                    A series of step motors with IP67 protection have been designed by JVL for use with the entire range of JVL Step Motor Drivers and Controllers. Torque from 0,5Nm to 8,2Nm. Even shaft sealing can be IP67 for harsh industrial operation.

                    • Special IP67 sealing at rear end and between stator and flanges
                    • Special Teflon IP67 shaft sealing
                    • Cost-Effective in harsh wet environment
                    • Ideal for food processing, pharmaceutical and chemical industries
                    • A double shaft seal and leak-proof cable entry provide watertight sealing
                    • The material of shaft is stainless steel SUS303/EN 1.4305/AISI303
                    • 2 phase motor. 200 step/rev.
                    • High torque-to-inertia for faster start and stop
                    • Rugged design and long life bearings
                    • High power, cooler running, rare-earth magnet design
                    • Exposed-lamination housing, optimized for high torque and smooth, accurate microstepping
                    • NEMA23 (57x57mm), NEMA26(60x60mm) and NEMA34 (86x86mm) mounting
                    • Very short length and very high torque/mm3
                    • High axial and radial shaft load
                    • Cost-effective alternative to servo motors
                    • All motors are D-shaped
                  • NEMA 23/24/34 Stepper Motors with IP67 Protection

                    • 57mm (2.3 inches) NEMA23 1.1Nm - 2.0Nm (155.8 oz-in) - (283.2 oz-in)
                    • 60mm (2.4 inches) NEMA24 1.3Nm - 3.0Nm (184.1 oz-in) - (424.8 oz-in)
                    • 87mm (3.4 inches) NEMA34 5.0Nm - 9.2Nm (708.1 oz-in) - (1302.8 oz-in)

                    A series of step motors with IP67 protection have been designed by JVL for use with the entire range of JVL Step Motor Drivers and Controllers. Torque from 0,5Nm to 8,2Nm. Even shaft sealing can be IP67 for harsh industrial operation.

                    • Special IP67 sealing at rear end and between stator and flanges
                    • Special Teflon IP67 shaft sealing
                    • Cost-Effective in harsh wet environment
                    • Ideal for food processing, pharmaceutical and chemical industries
                    • A double shaft seal and leak-proof cable entry provide watertight sealing
                    • The material of shaft is stainless steel SUS303/EN 1.4305/AISI303
                    • 2 phase motor. 200 step/rev.
                    • High torque-to-inertia for faster start and stop
                    • Rugged design and long life bearings
                    • High power, cooler running, rare-earth magnet design
                    • Exposed-lamination housing, optimized for high torque and smooth, accurate microstepping
                    • NEMA23 (57x57mm), NEMA26(60x60mm) and NEMA34 (86x86mm) mounting
                    • Very short length and very high torque/mm3
                    • High axial and radial shaft load
                    • Cost-effective alternative to servo motors
                    • All motors are D-shaped
                  • High Torque Stepper Motors MST34xxx3 up to 12,5Nm

                  • A series of high torque stepper motors.
                    87mm (3.4 inches) NEMA34 3.2Nm - 12.5Nm

                    A series of step motors that have been designed by JVL for use with the entire range of JVL Step Motor Drivers and Controllers. They are high torque step motors especially made for mini- and microstep operation.

                    • Highest torque density rating in the industry
                    • High torque-to-inertia for faster start and stop
                    • Rugged design and long life bearings
                    • High power, cooler running, rare-earth magnet design
                    • Exposed-lamination housing, optimized for high torque and smooth, accurate microstepping
                    • Standard NEMA34 mounting
                    • Facilities for encoders, double shaft, different shaft types, etc.
                    • Ground terminal for correct EMC shielding
                    • High axial and radial shaft load
                    • Cost-effective alternative to servo motors
                    • Low noise Option for planetary gearhead
                  • High Torque High Precision Stepper Motors MST34xxx2 up to 9Nm

                  • A series of high torque stepper motors with high precision.
                    87mm (3.4 inches) NEMA34 3Nm - 9Nm

                    A series of step motors that have been designed by JVL for use with the entire range of JVL Step Motor Drivers and Controllers. They are high torque step motors especially made for mini- and microstep operation.
                    Compared to the motor MST34xxx3 this motor is produced in higher quality with less mechanical and electrical tolerances making it more suitable for applications that require repetitive and uniform motors. It also offers better protections against water and use better balls bearings etc. This motor is not developed/produced in China.

                    • Highest torque density rating in the industry
                    • High torque-to-inertia for faster start and stop
                    • Rugged design and long life bearings
                    • High power, cooler running, rare-earth magnet design
                    • Exposed-lamination housing, optimized for high torque and smooth, accurate microstepping
                    • Standard NEMA34 mounting
                    • Facilities for encoders, double shaft, different shaft types, etc.
                    • Ground terminal for correct EMC shielding
                    • High axial and radial shaft load
                    • Cost-effective alternative to servo motors
                    • Low noise Option for planetary gearhead
                  • High Torque Stepper Motors MST43xxx2 up to 25Nm

                  • A series of high torque stepper motors.
                    109mm (4.3 inches) NEMA43 10Nm - 24Nm

                    A series of step motors that have been designed by JVL for use with the entire range of JVL Step Motor Drivers and Controllers. They are high torque step motors especially made for mini- and microstep operation.

                    • Highest torque density rating in the industry
                    • High torque-to-inertia for faster start and stop
                    • Rugged design and long life bearings
                    • High power, cooler running, rare-earth magnet design
                    • Exposed-lamination housing, optimized for high torque and smooth, accurate microstepping
                    • Standard NEMA43 mounting
                    • Facilities for encoders, double shaft, different shaft types, etc.
                    • Ground terminal for correct EMC shielding
                    • High axial and radial shaft load
                    • Cost-effective alternative to servo motors
                    • Low noise Option for planetary gearhead
                  • High Torque Stepper Motors MST51x up to 50Nm

                  • A series of high torque stepper motors.
                    134mm (5.1 inches) NEMA51 27Nm - 50Nm

                    This high torque stepper motor can be used for application that demand extreme high torque at low speed. With a flange size 134x134mm and length 270mm can this motor deliver up to 50Nm holding or running torque.

                    MST511 27Nm 165mm
                    MST512 40Nm 230mm
                    MST513 50Nm 270mm

                    • Industrial connector for high IP protection.
                    • Highest torque density rating in the industry.
                    • High torque-to-inertia for faster start and stop.
                    • Rugged design and long life bearings.
                    • High power, cooler running, rare-earth magnet design.
                    • Exposed-lamination housing, optimized for high torque and smooth, accurate microstepping.
                    • Standard NEMA51 mounting.
                    • High axial and radial shaft load.
                    • Cost-effective alternative to servo motors.
                    • Optional with build in controller SMC85 with PLC and Ethernet.
                • Stepper Motors Linear Actuator NEMA08 to NEMA34

                • Linear Stepper Motors can dramatically reduce cost and save space. There is no coupling, no additional bearing support and no assembly work required. This not only reduce cost but also reduce failure rate due to the less number of components and more simple construction. In applications with small load ratings a linear guide is also not required. The special design and material of the nut secure long life operations.
                    • NEMA17 42mm Stepper Motor Linear Actuators: 90 - 720 Newton (N)

                    • 90 - 720 Newton (N) - 0.3 - 195.1 mm/s

                      Linear stepper motors can dramatically reduce cost and save space. There is no coupling, no additional bearing support and no assembly work required. This not only reduce cost but also reduce failure rate due to the less number of components and more simple construction. In applications with small load ratings a linear guide is also not required. The special design and material of the nut secure long life operation.

                      Below versions can be delivered

                      • Captive linear actuator with built-in guider for linear movements. Moving part do not rotate.
                      • Non-Captive linear actuator with nut inside motor. Linear moving part can rotate so it should be fixed.
                      • External linear actuator. Nut are mounted on lead screw.
                      • Captive (will be available for NEMA34 in the future) and External linear actuator in NEMA size 23 and 34 can be delivered with integrated driver or controller.
                    • NEMA23 57mm Stepper Motor Linear Actuators: 100 - 1400 Newton (N)

                    • 100 - 1400 Newton (N) - 0.3 - 381.0 mm/s

                      Linear stepper motors can dramatically
                      reduce cost and save space. There is no coupling, no additional bearing support and no assembly work required. This not only reduce cost but also reduce failure rate due to the less number of components and more simple construction. In applications with small load ratings a linear guide is also not required. The special design and material of the nut secure long life operation.

                      Below versions can be delivered:

                      • Captive linear actuator with built-in guider for linear movements. Moving part do not rotate.
                      • Non-Captive linear actuator with nut inside motor. Linear moving part can rotate so it should be fixed.
                      • External linear actuator. Nut are mounted on lead screw.
                      • Captive (will be available for NEMA34 in the future) and External linear actuator in NEMA size 23 and 34 can be delivered with integrated driver or controller.
                    • NEMA23 57mm Integrated Stepper Motor Linear Actuator: 100 - 1400 Newton (N)

                    • 100 - 1400 Newton (N) - 0.3 - 381.0 mm/s.

                      Linear stepper motors can dramatically reduce cost and save space. There is no coupling, no additional bearing support and no assembly work required. This not only reduce cost but also reduce failure rate due to the less number of components and more simple construction. In applications with small load ratings a linear guide is also not required. The special design and material of the nut secure long life operation.

                      Below versions can be delivered

                      • Captive linear actuator with built-in guider for linear movements. Moving part do not rotate.
                      • External linear actuator. Nut are mounted on lead screw.
                      • Captive (will be available for NEMA34 in the future) and External linear actuator in NEMA size 23 and 34 can be delivered with integrated driver or controller.
                    • NEMA34 86mm Integrated Stepper Motor Linear Actuator: 400 - 2700 Newton (N)

                    • 400 - 2700 Newton (N) - 1.3 - 152.4 mm/s

                      Linear stepper motors can dramatically
                      reduce cost and save space. There is no coupling, no additional bearing support and no assembly work required. This not only reduce cost but also reduce failure rate due to the less number of components and more simple construction. In applications with small load ratings a linear guide is also not required. The special design and material of the nut secure long life operation.

                      Below versions can be delivered

                      • Non-Captive linear actuator with nut inside motor. Linear moving part can rotate so it should be fixed.
                      • External linear actuator. Nut are mounted on lead screw.
                      • Captive (will be available for NEMA34 in the future) and External linear actuator in NEMA size 23 and 34 can be delivered with integrated driver or controller.
                  • Software

                  • Software for setup and programming. An OCX/ ActiveX driver for programmers of Windows applications. For those who want to make their own interface and send serial data from a PLC, PC or microprocessor a MACtalk protocol analyzer and viewer is available. MotorSizer.com makes it easy to determine the required motor and gear size for a specific task.
                      • Commisioning Tool MacTalk

                      • Setup and diagnosis software for JVL integrated servo - and stepper motors.

                        With JVL’s MacTalk it is easy to setup and diagnose a MAC or QuickStep motor.

                        MacTalk includes everything that is needed to setup, tune and maintain the electronics and the motor.

                        The filter setup for the motors is done easily by a graphical selection chart. There is no easier way to do it.

                        In combination with mechanics the oscilloscope function can help to identify the tricky parts of the movement.

                      • Programming support. MACCOMM OCX

                      • OCX / Active X software helps you to interface fast and easily with a PC or industrial PC via RS232 or RS485 serial interface.

                        This software translates the data to and from the JVL MacTalk protocol so that you don’t have to worry about start and stop byte, checksum and retry. By using this software you do not need to understand the JVL protocol but only have to think about what’s important for you and that is to send data to the correct motor and register. You just send address, register number and value to a function and the driver see to that start and stop byte, checksum calculation and retransmission is done automatically. Additional it helps you with automatic calculation from an internal motor unit to eg. RPM and RPM/s 2. This is very useful when you have more JVL integrated motors like MAC140, MAC800 and MIS232 or the Controller SMC75 on the same serial line. You can interface to the most common software languages like:

                        • Visual Basic
                        • Visual C++
                        • Visual .Net
                        • Delphi
                        • Borland C++ Builder
                        • LabView
                        • Excel
                      • Expert tool for programmers. MACREGIO

                      • If you would like to learn more about the MacTalk protocol this is the software that you need. When you are using a PLC and would like to send commands to the integrated motor you need to send data in a special format called MacTalk protocol. MacTalk protocol is not ASCII but binary, message-oriented. This means that you can’t use a windows terminal editor to communicate with the motor but need to use MacTalk, MACREGIO or send byte commands.

                        In the MACREGIO can you see a complete overview with register and description for all MAC motors, QuickStep MIS23x and SMC75. By pressing "R” you can read register´s content and by pressing "W” you can write a value to a register. You can see register value and if a register is a Word, integer or Longint.
                        As an extra help for the programmer the byte send and received is shown byte for byte so it is easy to see what should be send and what to expect as returned. Thereby implementation and debugging is very easily done.

                    • Touch Operator Panels

                    • Wide range of high quality Human Machine Interface panels for use with the integrated servo and stepper motors from JVL.
                          • Touch Operator Panels for QuickStep and MAC integrated motors

                          • Wide range of high quality Human Machine Interface panels for use with the integrated servo and stepper motors from JVL.

                            JVL now provide a wide range of excellent HMI operator panels for all our integrated motors.
                            Available screen sizes from 4,3" to 15" with resolutions up to 1024 x 768.
                            Enjoy easy creation of operator screens using the EV5000 development software package for Windows.
                      • Planetary, Robot and Worm Gears

                      • A series of gears for use with the JVL range of Integrated Servo and Stepper motors as well as with other motors in the JVL range.
                          • Low Cost Planetary Gears

                          • If your application is cost sensitive and you don't need high perfomance the HMGH series is the right choice.

                            Nominal Torque: 6 Nm
                            Ratios: 3:1...100:1
                            Backlash: 120 arcmin
                            Efficiency: 60...90  %

                            The series of HMGH planetary gears are specially designed for JVL. With their NEMA23 standard flanges they can be directly mounted on the MAC 050 to 141 series of integrated motors as well as on a wide range of stepmotors. They also fit directly on the new integrated step motors, QuickStep.
                            Gears with other flanges can also be delivered from this series.

                            • NEMA23 standard configuration on input and output flange.
                            • All powder metal gears except adapter.
                            • Operating temperature range: 0 - 40°C ambient.
                            • Absolute max. 90°C.
                            • Maximum input speed: 4000rpm.
                            • Axial load 34kg max.
                            • Radial load 34kg max. at 15.8mm from shaft end.
                            • Very low losses.
                            • High efficiency.
                            • Low cost
                          • HFOS Worm Gears

                          • If cost is important and you also need a 90° angle - then our Worm gear boxes should be your first choice. Use the MAC141-A1AFAG which is a standard MAC 141 motor build with an 8 mm special shaft and round flange: it fits directly on the HFOS gear series.

                            Nominal Torque: 9...21 Nm
                            Ratios: 6:1...75:1
                            Backlash: depends on conditions
                            Efficiency: 36...77  %

                            • Gear ratios from 6:1 to 75:1
                            • Small build-in length, appx. 73 mm
                            • Inexpensive solution for many less demanding applications
                            • Adaptor kit for NEMA23 flanges
                            • Can be adapted to customer application
                            • Simpel and robust design

                            Angled worm gears for NEMA23 motors

                            The HFOS gears are a series of inexpensive, very compact worm gears. By means of an adaptor Kit they can be mounted directly on motors with a NEMA23 standard flange, such as the MAC050-141 series of integrated AC servo motors and QuickStep integrated step motors. They will however also find applications with a wide range of common stepper motors with NEMA23 flanges. 

                            These gears offer the advantage over planetary gears that they by nature are angled and gives a very short total length of motor plus gear. 

                            The gears can be delivered both right- and left-angled as well as with output shaft to both sides. A wide range of gearing ratios, from 6:1 to 75:1 are available. 

                            When ordering, various worm and cogwheel materials can be chosen in order to optimize the gear for the application. 

                            On the output side the gears can be delivered with a 30 mm machined recess for centering and 4 M5 threaded mounting holes. 

                            A mounting fixture is available for mounting of the motor-gear combination

                          • Worm gears HTTW

                          • This worm gear range allows you to supply compact sized stepper and servo gear motors for applications in many sectors that have limited dimensions and where high torque, hollow shaft and low cost is a necessity.

                            Nominal Torque: 12...166 Nm
                            Ratios: 5:1... 100:1
                            Backlash: Depends on conditions
                            Efficiency: 50...70  %

                            This worm gear range allows you to supply compact sized stepper and servo gear motors for applications in many sectors that have limited dimensions and where high torque, hollow shaft and low cost is a necessity.

                            • Gear ratios from 5:1 to 100:1
                            • Output torque 12-166Nm. Up to 4KW
                            • Efficiency 50-70%
                            • Flanges for all JVL motors
                            • Assembly in many positions
                            • Die-cast aluminium housing for worm gearboxes
                            • Permanent synthetic oil long-life lubrication
                            • High reliability and space saving
                            • Many gears on stock
                          • Precision Planetary Gears Type HTRG

                          • When you need an honest hard working Planetary gear box think of our HTRG series. We provide them with std backlash of 15 or 10 arcmin (1+2 stage) and also with high precision reduced backlash of either 5 or 3 arcmin

                            Nominal Torque: 12...1000 Nm
                            Ratios: 3:1...1000:1
                            Backlash: 3...17 arcmin
                            Efficiency: 90...97  %

                            The HTRG product range of precision planetary gears is the outcome of years of experience in the industry, and is the culmination of a decade-long dedication to performance enhancement. Comprising a wide range of low backlash planetary gearboxes, the units come in a range of precision classes up to 3’, and are available in seven gear frame sizes, with one or more reduction stages for gearing ratios from 1:3 to 1:1000. Double shaft, right angle shaft and right angle output shaft versions are also available. All this, combined with tens of motor mounting adapters held in stock, mean we can quickly respond to the most diverse application requirements of our customers. The gears can be mounted directly or by means of adaptor flanges on most of the JVL integrated servo and stepper motors as well as on the wide range of other motors from JVL. This datasheet shows the HTRG types of gear boxes which JVL normally has in stock for JVL motors and often delivered types.
                            If a special type of gear box, a special ratio, less backlash, angled types etc. is not shown in the datasheet and is needed, then contact JVL Industri Elektronik and we’ll find a type or a solution.

                          • Precision Planetary Gears Type HAGG

                          • The most precise Planetary gear box we can deliver is our HAGG series from Wittenstein - better know as Alpha gear boxes. We provide them with backlash from 1 to 25 arcmin. Select them when you need the highest quality and performance, and you will get trouble-free operation for a very long time.

                            Nominal Torque: 15...6000 Nm
                            Ratios: 3:1... 100:1
                            Backlash: 1..25
                            Efficiency: 90...97  %

                            Products manufactured by WITTENSTEIN alpha GmbH are setting benchmarks worldwide in the fields of mechanical engineering and drive technology.

                            From low backlash planetary gearheds and servo right-angle gearheads to the comprehensive cymex® engineering software package.

                            WITTENSTEIN alpha GmbH has redefined the meaning of precision, an essential benchmark and the most important attribute of their products.

                            Precision classes down to 1’ — and gearing ratios from 3:1 to either 100:1 (straight) or 10.000:1 (right-angled).

                            Order top precision Alpha gear boxes and they will fit perfectly to MAC motor® and QuickStep®.

                          • Backlash free Robot Gears

                          • Combine your bearing and backlash free gear box into one unit - the HSPG Spinea reducer. Unbeatable specs and perfomance made companies like KUKA and ABB prefer these reducers in their robots, which really must run perfectly 24-7. Also very suitable for turn tables, antennas, cameras, radars and e.g. tools in moulding machines.

                            Nominal Torque: 37...2940 Nm
                            Ratios: 33:1...191:1
                            Backlash: <1 arcmin
                            Efficiency: 50...95 %

                            Combine your bearing and backlash free gear box into one unit - the HSPG Spinea reducer. Unbeatable specs and perfomance made companies like KUKA and ABB prefer these reducers in their robots, which really must run perfectly 24-7. Also very suitable for turn tables, antennas, cameras, radars and e.g. tools in moulding machines.

                            • Zero backlash
                            • Integration of high capacity radial-axial bearings into the reduction gear
                            • Almost 100% increase of the rated torque
                            • More than 90% transmission efficiency by rated torque
                            • Large scale of reduction ratio (31-191)
                            • High precision performance
                            • High linearity of the torsion characteristics
                            • Elimination of the gliding friction from the reduction mechanism
                            • Very low level of noise and vibration
                            • Very simple construction
                            • Decreased external dimensions
                            • High reliability
                            • Long service life
                        • Electronic Motor Brake and Shaft Reinforcement

                        • The electronic brake is designed and produced by JVL to be mounted on stepper- and servo motors that have NEMA23 and NEMA34 flange such as the MAC50-141 series of integrated servo motors and the series of QuickStep MIS23x and MIS34x integrated stepper motors. The brake has zero backlash and no auditory noise. It fits on all step- and servo motors with NEMA23 and NEMA34 flange and can from stock be delivered with different input and output shaft. Connection can be wire or M8 connector. Protection from IP44 to watertight IP67.
                            • MAB23x, NEMA23, 57x57mm, 0.5 to 1.5 Nm.

                            • The electronic brake MAB23x is designed by JVL to be mounted on stepper or servo motors with NEMA23 flange. They can be mounted on JVL motor MAC050, MAC095, MAC140 and MAC141 series of integrated servomotor and MIS231,MIS232 and MIS234 series of integrated stepper and the MST23x series of rotating stepper motors. The brake has zero backlash and no auditory noise and can be delivered with different input and output shaft dimensions.
                            • MAB34x, NEMA34 86x86mm 1.7Nm

                            • The electronic brake MAB34x is designed by JVL to be mounted on stepper or servo motors with NEMA34 flange. They can be mounted on JVL motor MIS340,MIS341 and MIS342 series of integrated stepper motors and the MST34x series of rotary stepper motors. The brake has zero backlash and no auditory noise and can be delivered with different input and output shaft dimensions.
                               
                          • Encoders

                          • JVL offers a range of encoders. Both linear and rotating, Incremental, magnetic, absolute multiturn. SSI and BISS.

                            JVL is Exclusive distributor for LIKA Electronics and Givi Misure rotational and linear encoders.
                                • JVL Linear and rotating encoders. Absolute multiturn and SSI

                                • Typically, absolute-encoders are used when there is a need to continue operation immediately after power is re-applied to a machine or system, without first having to perform a zero-search reset. Thereby the cost for sensor and mounting time is saved Another major reason for using absolute encoders is to correct motor position in relation to the actual physical absolute position measured. All encoders can be mounted on its own connector on the JVL motor, stepper or servo. No need for external power supply or connection boxes, because the encoder is powered via the same cable from the integrated motor.  The SSI interface is used with double or triple reading to secure reading even in noisy environment.  The rotational encoder can be delivered as a magnetic based low cost version with 1 degree error or a high precision optical version with 0.05 degree error.  Magnetic Linear encoders have precision down to 50µm and can therefore be used for high precision application at a low cost. With it''s obvious advantages, the Magnetic measurement system is a valid alternative to traditional linear and rotative transducers. The system operates without contact and is unaffected by dirt, grease and water.
                            • Power Supplies

                            • A wide range of highly efficient switchmode power supplies for supplying the entire range of JVL integrated MAC ac servo motors and integrated QuickStep stepper motors.
                                • Power Supply PSU24-075

                                • 24V, 75W Switchmode Power Supply for supplying MAC Expansion Modules, In- and Outputs etc with 24VDC
                                • Power Supplies PSU40, PSU80 and PSU150

                                • A wide programme of compact and robust industrial power supplies for motor controllers that do not have their own power supply. Can also be used as a supplement to a built-in power supply in order to fulfil special requirements. 200W, 400W and 1200W versions.
                                • Power Supply Kits for Motor Drivers and Controllers

                                • These power supplies can be used in applications when there is insufficient space for a standard power supply or a more cost-effective solution is required.
                                • Switch Mode Power Supplies PSU48 - 240

                                • A modern switchmode supply that is particularly well suited for supplying the range of integrated MAC motors with 48Volts DC
                                • Other Switch Mode Power Supplies

                                • A full range of highly efficient switchmode power supplies ideally suited for supplying the entire range of JVL integrated MAC motors and JVL stepper motor drivers.
                                • Power Supplies PSU48/12-2 and PSU48/24-2

                                • 12 VDC to 24VDC and 48VDC Power Supplies
                                • Switch Mode Power Supplies PSU80-1000-10

                                • A 1000W switchmode power supply that are particularly well suited for supplying the range of JVL integrated servo and steppermotor or other driver/controller with supply voltage in the range 70-90VDC. Ultra compact with dimension 110x125x150mm and only 2,5kg makes it the most compact 80V/1000W power supply in the industry. Can be used together with JVL integrated stepper motor MIS340-MIS343 and stepper driver SMD41 series.
                              • Connection cables

                              • A series of cables and connectors for the MAC integrated servo motors and the QuickStep integrated stepper motors.
                                    • M12 Connection Cables

                                    • M12 connection cables for MAC Motor Expansion Modules and the QuickStep Motors

                                      In order to ease installation of the MAC and QuickStep motors with M12 connectors, JVL has developed a series of ready-made cables and adaptors etc. In the table in the data sheet we have listed all items available and indicated which cables that should be used with which expansion module.